Archive | Project 2: Digital Tattoo Machine RSS for this section

New Tattoo Machine Diagram

To celebrate one year since finishing the tattoo machine, I thought I would upload a new diagram I have been working on for my portfolio. This is an exploded perspective of the final tattoo machine. Almost everything that is not labeled is a 3d printed part (which can be found in my previous tattoo machine post) or a stepper/servo motor. For clarity I decided not to add in all of the screws and nails that were required to put this piece together as they should be fairly obvious by the hole placements in the 3d printed parts.

Final Prints

ImageAfter 3d printing over forty different iterations and test pieces, these are the final 17 that are used in the tattoo machine. If for any reason you want the .stl files just PM me and I will send them to you. I hope this project inspires some people to make their own tattoo machines or something even cooler!

Digital Tattoo Machine

This is the last video I will post of the tattoo machine in action. I haven’t posted a 1x speed video recently so this one shows the full process at regular speed. The video can also be found here at 4x speed if this one is going too slow.

Final Design

ImageThese photos depict the final design for the digital tattoo machine. The machine took one a half months from start to finish and I have learned a lot from building it. There are still a few areas which aren’t perfect, but it functions well enough to do outlines of any design that you give it. The only area I see that really needs to be improved is filling in a shape as that has caused some difficulties.

The tattoo machine can be calibrated to any size arm and it only takes 25 minutes to get a high resolution scan. From there, small tattoos take anywhere between 1 and 3 minutes whereas longer ones that need to be filled in can take up to half an hour.

Read More…

The Code

A lot of the code is just taking example code from the AF_Motor library as well as the Firefly Firmata and making slight changes to them. The calibration uses both Processing and Arduino but the tattoo drawing just uses Arduino thanks to the Firefly plugin to Grasshopper. Below the code is also two low res images of the grasshopper files.

Read More…

Mickey Mouse and Octopus

This 8x speed video for these two tattoos will be one of the last for this project. The octopus was a huge success as it came out almost perfectly and it shows how far the tattoo machine can be pushed to get good results. The Mickey Mouse tattoo on the other hand didn’t come out very well and the motors were starting to slow because of battery drain, so much so that I stopped it halfway though.

I could continue to tweak the grasshopper file to make sure that filling in the tattoo shapes come out perfectly but I am not going to at this point. I may come back and revisit this project at a later date but right now I am ready to move on to my next idea. Click the picture below for a moving gif of the octopus.

Read More…

Running Dog Tattoo

This video is sped up 16x, but it shows how multiple lines are drawn. On the computer screen you can sort of see how the lines are drawn but unfortunately it is out of focus. When the pen gets to the end of a line it lifts up and moves while hovering above the arm until it gets to the next point where it then comes back down to the arm to start drawing again.

First Multiple Line Tattoo

ImageThis was the first time that I tried a multiple line tattoo and I learned a few things from it. I currently have the pen move at the same speed when it is going above the arm as it is when it is drawing on the arm. This causes the pen to move unnecessarily slowly, but at this point I am not quite sure how I would change the grasshopper file to allow the pen to move faster. 

I had good luck with multiple figures, but when filling in the dog I had the spacing about twice as wide as it needed to be. The whole running dog tattoo was supposed to take 20 min with the lines being 0.6 cm apart, which means it would probably take about 35 minutes to fill it in correctly. I stopped this tattoo after only about 7 of the 20 minutes because I knew what the end result would be.

First Good Tatoo 4x Speed

This is the video that corresponds with my previous post titled “Expectation becomes Reality” (referencing my earlier post Expectation vs Reality). Everything looks and works pretty much the way I want it and there are just a few minor problems left.

I had to move my arm small amounts (less than a cm at a time) about four or five times over the course of the video to get my arm to be positioned better with the pen. Sometimes I had to move my arm down because the pen was pressing too hard, while other times I had to shift my arm over to get better contact with the pen. Overall I think that this is really just a calibration problem and that if I re-calibrate more carefully these problems will go away.

The new stepper motor is the loud and that is the noise you hear on the video. I think the noise is actually coming from the teeth of the timing pulley going against the grains of the 3d print, and while it isn’t too annoying I would like to find a fix for it.

Expectation becomes Reality

ImageFor the first time this project I am content with final outcome of the tattoo. It is by no means perfect or something you would want replicated by a professional tattoo artist, but for what I am trying to do it is close enough.

To complete this project the only things left to do are draw a tattoo that is filled in and draw a tattoo that is made up of more than one part. All of the tattoos this far have been one continuous line to make the process easier. This is not very practical for a real tattoo that would normally be made up of many lines that together form a whole. In an earlier post I showed an example of how I would break up an image into contoured lines but I still haven’t actually implemented it in a tattoo.